ADTO News

• 

  Property of Fireproof and Anti Sand Accumulation of Scaffolding Planks

  Hot dip galvanized steel scaffolding planks plate with fire prevention, prevent many sands, light weight, corrosion resistance, alkali resistance and high compressive strength, surface convex hole, on both sides of the h design effect than similar products is particularly significant, standardization, pitch trim molding surface exclusive double reinforcement design, increased the strength, good appearance, durable (normal construction can use continuously 6-8 years) characteristic of the

  2016-12-07
• 

  Specifications, Sizes and Types of Regular Steel Scaffolding Planks

  Steel scaffolding planks are used in shipbuilding, repairing yard and construction in the construction works, installation enterprises set up scaffolding supporting the use of a kind of form a complete set of tools. Hunan ADTO company introduction of foreign advanced automatic steel board production lines, production speed, each class can out of the 900-1000 pieces of products continuously. This product is fireproof, light weight, corrosion resistance, alkali resistance and high compressive strength, surface convex hole with double border slip effect is good.

  2016-12-06
• 

  The Advantages of Using Hot Dip Galvanized Steel Scaffolding Planks

  A, using low cost: To each big shipbuilding enterprises currently using the comparison of several kinds of scaffolding and hot dip galvanized steel scaffolding planks: According to size (length x width x height) price comparison premium scrap recycling value. Hot dip galvanized steel scaffolding planks 3000 two-thirds mmx240mmx65mm board price without a 35% - 40% Angle steel plates 3000 mmx240mmx65mm 3/4 each year to replace the steel net iron board price

  2016-12-06
• 

  What Are the Specifications of Galvanized Steel Scaffolding Planks?

  On market at present, the common galvanized steel Scaffolding Planks specification is 2.0 m * 45 mm * 210 mm, 3.0 m 45 mm * 210 mm * 240 mm, 3.0 m * * 45 mm this three kinds of specifications, steel Scaffolding Planks for routine production material thickness is 1.2 mm. And ADTO company production of steel board size (width * thickness) : 45 mm, 210 mm * 210 mm * 45 mm, 50 mm * 250 mm, 50

  2016-12-05
• 

  Construction Steps and Precautions for the Attached Scaffolding Planks

  Scaffolding planks attached lifting scaffolding, steel construction steps and matters needing attention attached lifting scaffolding steel Scaffolding planks) (referred to as the "overall ascension (steel Scaffolding planks) scaffold" the body of the rack is designed according to the three stories high with fasteners (steel Scaffolding planks) type steel pipe scaffold set-up, bar at the bottom of the truss structure, mining play end bearing tripod, bearing a tripod is used through walls bolts on has finished

  2016-12-05
• 

  How Is the Momentum of Galvanized Scaffolding Planks in Domestic Market

  Galvanized steel planks is more a kind of building material used in our country, the material is not only applied in the construction industry is larger, more important in our country and some other family the installation in the shipbuilding industry also has a great role. So every steel board manufacturers in the production and sales of the products constantly, for steel board manufacturer, these are the business opportunities. However steel planks is ordinary steel and galvanized steel planks, galvanized steel planks

  2016-12-04
• 

  Scaffolding Planks Help You Obtain High Effieciency in the Construction

  Now with the continuous development of major ports, demand for ships is becoming more and more big, and for Marine facilities and construction, and other requirements are also increasing. So the ship construction in various materials, facilities are in constant improvement, better material selection. In ship construction, there is a kind of tool is cannot little, that is steel plank. Plank is used for plate and steel plate connection, adjust the width at the bottom of the platform, for the workers

  2016-12-04
• 

  Structural Requirements of Scaffolding When Design the System

  1.1 the general design size Poling throw of 1.8 m (partial adjustments, but no more than 1.8 m), horizontal distance of 0.9 m (can be flat out three pieces of bamboo scaffolding,each scaffolding bamboo string width 250 mm), the bent frame interval of 1.83 m, the outer shelf step distance of 0.915 m (safety specifications for 6 m by 18 m, taut after slightly more than 1.8 m wide, such as double step

  2016-12-01
• 

  Innovation Is the Key To the Development of Ringlock Scaffolding

  Scaffolding industry has a rapid development, scaffolding rental market is increasingly competitive, many companies face the grim problem of sales. In the face of such situation, enterprises need to innovate, to open a new situation, new market, so as to not be eliminated in market competition, which requires our continuous innovation, continuous development. Technological innovation is an important part of enterprise innovation, innovation is under the

  2016-12-01
• 

  The Dismantlement of Scaffolding Be Done in Such Way

  In dismantled scaffolding, end start to remove the top of the armrest and baluster, then remove the pedals (or level) in order to remove the escalator, interspersed with pole, door frame, take out the core. Put step gantry scaffolding down next door after the removal of scaffold, until the basement. Removal of connecting parts, should be the pin on the pin board and card hook to open position on the lock plate, not hard to pull, it is forbidden to tap and damaged parts. Set-up

  2016-11-30
• 

  How to Make the Scaffolding Steady in a Fast Way on the Site

  (1) to check in advance We need to pay attention to do a good job in checking before scaffolding, some with long time, with the decay of the set-up of scaffolding influence its stability, so try not to choose these products, also need to pay attention to the safety of every part. (2) regular job Scaffolding, you need to the fixed work of every step should be careful to do, to guarantee the

  2016-11-30
• 

  Requirement on the Use of Ringlock Scaffolding on the Site

  A stud spacing, generally not more than 2.0 m, poling horizontal distance not more than 1.5 m, even the wall not less than three spans, put a layer of fixed scaffolding full bottom, be put with scaffolding plank operation layer, since the operation layer down the plan, every 12 m to spread a layer of scaffolding. Size should be consistent with the construction fastener type steel pipe

  2016-11-29
• 

  What Are the Common Issues of Scaffolding Application During the Construction

  The heavy duty scaffolding should have a clear understanding, generally if the thickness of the floor more than 300 mm, should consider the design according to the heavy scaffolding, scaffolding load more than 15 kn/, the design should organize expert argumentation. (1)To separate the parts of the steel tube length changes on bearing, support for template should be considered: the top level of a rod of the centerline of the length of the template support a

  2016-11-29
• 

  How to Prepare the Basic (Ground) and Braced Structure

  (1) (to) should be the basis of scaffolding poling formation compaction, has enough bearing capacity and stability, in the pit or the stage, the stud from the edge of the pit shall not be less than 1 m, shall not be greater than soil slope and slope natural rest Angle, otherwise should be tested for slope protection and reinforcement. (2) scaffold made rod under uneven, solid or cant, must set up pad or plate.

  2016-11-28
• 

  How to Carry Out the Erection Process Of Scaffolding System

  A) before the erection of preparation 1. The technical personnel to the scaffold erection and site management personnel for technical, safety disclosure, not attend clarification personnel shall not participate in the erection work; Scaffolding, personnel must be familiar with the design content of scaffold. 2. The steel pipes, fasteners, scaffolding, gym, safety net of material, such as quality, quantity, counting, checking and acceptance, to ensure that meet the design requirements, and unqualified components shall not be used, shall not be connected when materials not neat,

  2016-11-28